在Matlab中读取Parula图像而不会丢失分辨率 [英] To imread Parula image in Matlab without losing resolution

问题描述

RGB和Parula之间没有双射，色彩映射到RGB三元组。但是，没有这样的一对一映射来反转此过程以将 parula 索引颜色转换回RGB（实际上有无数种方法可以这样做）。因此，两个空间之间没有一对一的对应关系或，它将RGB图像数据转换为索引图像数据。此功能使用在 $ c> colormap。

2015年6月20日更新： rgb2map 代码已更新为使用不同的颜色空间变换，这将其速度提高了近两倍。

There is no bijection between RGB and Parula, discussed here. I am thinking how to do well the image processing of files in Parula. This challenge has been developed from this thread about removing black color from ECG images by extending the case to a generalized problem with Parula colors.

Data:

which is generated by

[X,Y,Z] = peaks(25);
imgParula = surf(X,Y,Z);
view(2);
axis off;

It is not the point of this thread to use this code in your solution to read the second image.

Code:

[imgParula, map, alpha] = imread('http://i.stack.imgur.com/tVMO2.png'); 

where map is [] and alpha is a completely white image. Doing imshow(imgParula) gives

where you see a lot of interference and lost of resolution because Matlab reads images as RGB, although the actual colormap is Parula. Resizing this picture does not improve resolution.

How can you read image into corresponding colormap in Matlab? I did not find any parameter to specify the colormap in reading.

解决方案

The Problem

There is a one-to-one mapping from indexed colors in the parula colormap to RGB triplets. However, no such one-to-one mapping exists to reverse this process to convert a parula indexed color back to RGB (indeed there are an infinite number ways to do so). Thus, there is no one-to-one correspondence or bijection between the two spaces. The plot below, which shows the R, G, and B values for each parula index, makes this clearer.

This is the case for most indexed colors. Any solution to this problem will be non-unique.

A Built-in Solution

I after playing around with this a bit, I realized that there's already a built-in function that may be sufficient: rgb2ind, which converts RGB image data to indexed image data. This function uses dither (which in turn calls the mex function ditherc) to perform the inverse colormap transformation.

Here's a demonstration that uses JPEG compression to add noise and distort the colors in the original parula index data:

img0 = peaks(32);                     % Generate sample data
img0 = img0-min(img0(:));
img0 = floor(255*img0./max(img0(:))); % Convert to 0-255
fname = [tempname '.jpg'];            % Save file in temp directory
map = parula(256);                    % Parula colormap
imwrite(img0,map,fname,'Quality',50); % Write data to compressed JPEG
img1 = imread(fname);                 % Read RGB JPEG file data

img2 = rgb2ind(img1,map,'nodither');  % Convert RGB data to parula colormap

figure;
image(img0);                          % Original indexed data
colormap(map);
axis image;

figure;
image(img1);                          % RGB JPEG file data
axis image;

figure;
image(img2);                          % rgb2ind indexed image data
colormap(map);
axis image;

This should produce images similar to the first three below.

Alternative Solution: Color Difference

Another way to accomplish this task is by comparing the difference between the colors in the RGB image with the RGB values that correspond to each colormap index. The standard way to do this is by calculating ΔE in the CIE L*a*b* color space. I've implemented a form of this in a general function called rgb2map that can be downloaded from my GitHub. This code relies on makecform and applycform in the Image Processing Toolbox to convert from RGB to the 1976 CIE L*a*b* color space.

The following code will produce an image like the one on the right above:

img3 = rgb2map(img1,map);

figure;
image(img3);                          % rgb2map indexed image data
colormap(map);
axis image;

For each RGB pixel in an input image, rgb2map calculates the color difference between it and every RGB triplet in the input colormap using the CIE 1976 standard. The min function is used to find the index of the minimum ΔE (if more than one minimum value exists, the index of the first is returned). More sophisticated means can be used to select the "best" color in the case of multiple ΔE minima, but they will be more costly.

Conclusions

As a final example, I used an image of the namesake Parula bird to compare the two methods in the figure below. The two results are quite different for this image. If you manually adjust rgb2map to use the more complex CIE 1994 color difference standard, you'll get yet another rendering. However, for images that more closely match the original parula colormap (as above) both should return more similar results. Importantly, rgb2ind benefits from calling mex functions and is almost 100 times faster than rgb2map despite several optimizations in my code (if the CIE 1994 standard is used, it's about 700 times faster).

Lastly, those who want to learn more about colormaps in Matlab, should read this four-part MathWorks blog post by Steve Eddins on the new parula colormap.

Update 6-20-2015: rgb2map code described above updated to use different color space transforms, which improves it's speed by almost a factor of two.

这篇关于在Matlab中读取Parula图像而不会丢失分辨率的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！