如何在turbo C ++中运行以下代码？ [英] How can I run the following code in turbo C++?

问题描述

//This program is used to control a robot using a app
//Error Code Chart: Code 01; Turnradius is higher than Speed; Code 02; Speed is higher than 255;
#define in1 5 //L298n Motor Driver pins.
#define in2 6
#define in3 10
#define in4 11
#define LED 13
int command; //Int to store app command state.
int Speed = 204; // 0 - 255.
int Speedsec;
int buttonState = 0;
int lastButtonState = 0;
int Turnradius = 0; //Set the radius of a turn, 0 - 255 Note:the robot will malfunction if this is higher than int Speed.
int brakeTime = 45;
int brkonoff = 1; //1 for the electronic braking system, 0 for normal.
int pinmode(int, OUTPUT)
int analogwrite(int, Speed)
int digitalwrite(int, High)
void setup() {
  pinMode(in1, OUTPUT);
  pinMode(in2, OUTPUT);
  pinMode(in3, OUTPUT);
  pinMode(in4, OUTPUT);
  pinMode(LED, OUTPUT); //Set the LED pin.
  Serial.begin(9600);  //Set the baud rate to your Bluetooth module.
}

void loop() {
  if (Serial.available() > 0) {
    command = Serial.read();
    Stop(); //Initialize with motors stoped.
    switch (command) {
      case 'F':
        forward();
        break;
      case 'B':
        back();
        break;
      case 'L':
        left();
        break;
      case 'R':
        right();
        break;
      case 'G':
        forwardleft();
        break;
      case 'I':
        forwardright();
        break;
      case 'H':
        backleft();
        break;
      case 'J':
        backright();
        break;
      case '0':
        Speed = 100;
        break;
      case '1':
        Speed = 140;
        break;
      case '2':
        Speed = 153;
        break;
      case '3':
        Speed = 165;
        break;
      case '4':
        Speed = 178;
        break;
      case '5':
        Speed = 191;
        break;
      case '6':
        Speed = 204;
        break;
      case '7':
        Speed = 216;
        break;
      case '8':
        Speed = 229;
        break;
      case '9':
        Speed = 242;
        break;
      case 'q':
        Speed = 255;
        break;
    }
    Speedsec = Turnradius;
    if (brkonoff == 1) {
      brakeOn();
    } else {
      brakeOff();
    }
  }
}

void forward() {
  analogWrite(in1, Speed);
  analogWrite(in3, Speed);
}

void back() {
  analogWrite(in2, Speed);
  analogWrite(in4, Speed);
}

void left() {
  analogWrite(in3, Speed);
  analogWrite(in2, Speed);
}

void right() {
  analogWrite(in4, Speed);
  analogWrite(in1, Speed);
}
void forwardleft() {
  analogWrite(in1, Speedsec);
  analogWrite(in3, Speed);
}
void forwardright() {
  analogWrite(in1, Speed);
  analogWrite(in3, Speedsec);
}
void backright() {
  analogWrite(in2, Speed);
  analogWrite(in4, Speedsec);
}
void backleft() {
  analogWrite(in2, Speedsec);
  analogWrite(in4, Speed);
}

void Stop() {
  analogWrite(in1, 0);
  analogWrite(in2, 0);
  analogWrite(in3, 0);
  analogWrite(in4, 0);
}

void brakeOn() {
  //Here's the future use: an electronic braking system!
  // read the pushbutton input pin:
  buttonState = command;
  // compare the buttonState to its previous state
  if (buttonState != lastButtonState) {
    // if the state has changed, increment the counter
    if (buttonState == 'S') {
      if (lastButtonState != buttonState) {
        digitalWrite(in1, HIGH);
        digitalWrite(in2, HIGH);
        digitalWrite(in3, HIGH);
        digitalWrite(in4, HIGH);
        delay(brakeTime);
        Stop();
      }
    }
    // save the current state as the last state,
    //for next time through the loop
    lastButtonState = buttonState;
  }
}
void brakeOff() {

}

我尝试了什么：



它提供了很多错误，这是arduino的编码，但我必须在turbo C ++上执行此操作。

What I have tried:

it gives alot of errors, this is the coding of arduino but i have to do this on turbo C++.

推荐答案

该代码是为Arduino编写的，使用的是库中的方法，只有Arduino ...

简单的Turbo C项目将没有所有这些库，因此您将有一些编译错误。

结束即使您将以某种方式链接到正确的库，编译的代码也将在Arduino和您的计算机上失败...



所以，如果你想玩Arduino和机器人技术，那么使用Arduino IDE和主板...

如果你想要使用Turbo C和机器人技术，搜索正确的样本......

That code was written for Arduino and uses methods from libraries, that you have only on Arduino...
A simple Turbo C project will not have all those libraries, so you will have a few compilation error.
End even you will link somehow to the right libraries, the compiled code will fail on Arduino and on your computer as well...

So if you want to play with Arduino and robotics, than use Arduino IDE and board...
If you want to play with Turbo C and robotics, search for the right sample...

这篇关于如何在turbo C ++中运行以下代码？的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！