线性/非线性拟合正弦曲线 [英] Linear / Non-Linear Fit to a Sine Curve

问题描述

我看过

但是，如果您有权访问更多数据点，我的方法仍然是使用DFT。

更新：

我在数据上使用了Pisarenko的谐波分解（PHD），即使您的信号非常短（每个信号只有86个数据点），PHD算法绝对有潜力有更多可用数据。以下包括24个信号中的两个（数据的第11列和第13列），以蓝色表示，红色的正弦曲线对应于PHD估计的幅度/频率值。 （请注意，相移是未知的）

我使用MATLAB（pisar.m）执行PHD：

I've had a look at this and this.

But I have a slightly different problem. I know that my data is a sine curve, of unknown period and unknown amplitude, with additive non-gaussian distributed noise.

I'm attempting to fit it using the GSL non-linear algorithm in C, but the fit is absolutely terrible. I'm wondering if I'm (wrongly) using a non-linear fitting algorithm where I should be using a linear one?

How do I tell if a particular dataset requires a linear or a non-linear algorithm?

EDIT: My curve is really noisy, so taking an FFT to figure out the frequency may result in false positives and bad fits. I'm looking for a slightly more robust way of fitting.

The above plot has about a 170 points as you can see, and the plot below has about 790 points.

The noise is distinctly non-gaussian, and large compared to the amplitude of the data. I've tried FFT's on gaussian-distributed noise, and my fit was wonderful. Here, it's failing quite badly.

ADDED: Link to first time series data. Each column in the file is a different time series.

解决方案

If you know that your data is a sine curve, (which can be represented as a number of complex exponentials) then you can use Pisarkenko's harmonic decomposition; http://en.wikipedia.org/wiki/Pisarenko_harmonic_decomposition

However, if you have access to more data points, my approach would still to use an DFT.

UPDATE:

I used Pisarenko's harmonic decomposition (PHD) on your data, and even though your signals are extremely short (only 86 datapoints each), the PHD algorithm definately has potential if there is more data available. Included below are two (column 11 & 13 of your data) out of the 24 signals, depicted in blue, and the sine curve in red corresponds to the estimated amplitude/frequency values from PHD. (note that phase shift is unknown)

I used MATLAB (pisar.m) to perform PHD: http://www.mathworks.com/matlabcentral/fileexchange/74

% assume data is one single sine curve (in noise)
SIN_NUM = 1; 

for DATA_COLUMN = 1:24
    % obtain amplitude (A), and frequency (f = w/2*pi) estimate
    [A f]=pisar(data(:,DATA_COLUMN),SIN_NUM);

    % recreated signal from A, f estimate
    t = 0:length(data(:,DATA_COLUMN))-1;
    y = A*cos(2*pi*f*t);

    % plot original/recreated signal
    figure; plot(data(:,DATA_COLUMN)); hold on; plot(y,'r')
    title({'data column ',num2str(DATA_COLUMN)});

    disp(A)
    disp(f)
end

Which resulted in

1.9727     % amp. for  column 11
0.1323     % freq. for column 11
2.3231     % amp. for  column 13
0.1641     % freq. for column 13

VERIFICATION OF PHD:

I also did another test where I knew the values of amplitude and frequency and then added noise to see if PHD can estimate the values properly from the noisy signal. The signal consisted of two added sine curves with frequencies 50 Hz, 120 Hz respectively, and amplitudes 0.7, 1.0 respectively. In the figure below, the curve in red is the original, and the blue is with added noise. (figure is cropped)

Fs = 1000; % Sampling frequency
T = 1/Fs; % Sample time
L = 1000; % Length of signal
t = (0:L-1)*T; % Time vector

% Sum of a 50 Hz sinusoid and a 120 Hz sinusoid
x = 0.7*sin(2*pi*50*t) + sin(2*pi*120*t);
y = x + 0.4*randn(size(t)); % Sinusoids plus noise

figure;
plot(Fs*t(1:100),y(1:100)); hold on; plot(Fs*t(1:100),x(1:100),'r')
title('Signal Corrupted with Zero-Mean Random Noise (Blue), Original (Red)')

[A, f] = pisar(y',2); 
disp(A)
disp(f/Fs)

PHD estimated the amp/freq values to be:

0.7493    % amp wave 1  (actual 0.7)
0.9257    % amp wave 2  (actual 1.0)
58.5      % freq wave 1 (actual 50)
123.8     % freq wave 2 (actual 120)

Not bad for quite a bit of noise, and only knowing the number of waves the signal consists of.

REPLY @Alex:

Yeah it's a nice algorithm, I came across it during my DSP studies, and I thought it worked quite well, but it's important to note that Pisarenko's Harm.Dec. models any signal as N > 0 sinusoids, N being specified from start, and it uses that value to ignore noise. Thus, by definition, it is ONLY useful when you know roughly how man sinusoids your data is comprised of. If you have no clue of the value for N and you need to run the algorithm for a thousand different values, then a different approach is definately recommended. That said, evaluation is thereafter straightforward since it returns N amplitude and frequency values.

Multiple signal classification (MUSIC), is another algorithm which continues where Pisarenko left off. http://en.wikipedia.org/wiki/Multiple_signal_classification

这篇关于线性/非线性拟合正弦曲线的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！