如何在Windows下的FreePascal中检测stdin或stdout是否已重定向? [英] How do I detect if stdin or stdout is redirected in FreePascal under Windows?

问题描述

我需要知道是否已使用最新的FPC(v3.0.0)将stdin或stdout重定向到控制台应用程序

I need to know whether stdin or stdout has been redirected for a console application using the latest FPC (v3.0.0)

在过去的Turbo Pascal时代，我有一个用汇编语言编写的函数可以做到这一点.见下文:

In the old Turbo Pascal days, I had a function written in assembly that did this. See below:

{ **************************************************************
  * Routine   : RedirectedStd                                  *
  * Purpose   : Return Yes (True) if standard handle is being  *
  *           : redirected.                                    *
  * Note(s)   : Even though handle can take any handle value,  *
  *           : the function will be meaningful only for the   *
  *           : standard input, standard output, and standard  *
  *           : error.  It will, however, be True for any      *
  *           : handle that does NOT point to the console.     *
  *           : (Besides, this is what it actually checks for.)*
  *           : Make sure handle belongs to an open file or    *
  *           : you will get wrong answer (check IOResult).    *
  ************************************************************** }
function RedirectedStd(handle: Word): Boolean; assembler;
const
  DEVICE       = $0080;
  FASTCONSOLE  = $0010;
  CONSOUT      = $0002;
  CONSIN       = $0001;
asm
  mov     InOutRes,0
  mov     ax,$4400       { IOCTL svc, get device information }
  mov     bx,handle
  int     $21            { result in DX }
  mov     ax,1           { assume function is True }
  jc      @Error         { got error with code in AX }
  test    dx,DEVICE
  jz      @Out
  test    dx,FASTCONSOLE
  jz      @Out
  test    dx,CONSOUT
  jz      @Out
  test    dx,CONSIN
  jz      @Out
  xor     ax,ax          { function is False }
  jmp     @Out
@Error:
  mov     InOutRes,ax
@Out:
end; { RedirectedStd }

此语法对于FPC汇编器无效.我尝试了以下变体，尽管编译正常，但它崩溃了:

This syntax is not valid for the FPC assembler. I tried my luck with the following variant which although compiles OK it crashes:

function RedirectedStd(handle: Word): Boolean; assembler;
label Error,Done;
const DEVICE       = $0080;
      FASTCONSOLE  = $0010;
      CONSOUT      = $0002;
      CONSIN       = $0001;
asm
          movw      $0,InOutRes
          movw      $4400,%ax           { IOCTL svc, get device information }
          movw      handle,%bx
          int       $21                 { result in DX }
          movw      $1,%ax              { assume function is True }
          jc        Error               { got error with code in AX }
          test      DEVICE,%dx
          jz        Done
          test      FASTCONSOLE,%dx
          jz        Done
          test      CONSOUT,%dx
          jz        Done
          test      CONSIN,%dx
          jz        Done
          xor       %ax,%ax             { function is False }
          jmp       Done
Error:    movw      %ax,InOutRes
Done:
end; { RedirectedStd }

(不确定我的转换是否等效.)

(Not sure if my conversion is equivalent.)

有什么想法吗?

根据公认的答案，该答案为我提供了足够的方向来找出解决方案，我为我的原始例程提出了以下替代方案:

Based on accepted answer which gave me enough direction to figure out the solution, I came up with the following drop-in replacement for my original routine:

function RedirectedStd(handle: Word): Boolean; {$ifndef WINDOWS} unimplemented; {$endif}
begin
  RedirectedStd := False;
  {$ifdef WINDOWS}
  case handle of
    0: RedirectedStd := GetFileType(GetStdHandle(STD_INPUT_HANDLE)) <> FILE_TYPE_CHAR;
    1: RedirectedStd := GetFileType(GetStdHandle(STD_OUTPUT_HANDLE)) <> FILE_TYPE_CHAR;
    2: RedirectedStd := GetFileType(GetStdHandle(STD_ERROR_HANDLE)) <> FILE_TYPE_CHAR;
  end;
  {$endif}
end; { RedirectedStd }

哦，您需要使用Windows；

Oh, and you need to do Uses Windows;

推荐答案

使用

GetFileType(GetStdHandle(STD_OUTPUT_HANDLE));

用于标准输出.对于stdin应该做什么是显而易见的.

for stdout. It should be obvious what to do for stdin.

这篇关于如何在Windows下的FreePascal中检测stdin或stdout是否已重定向?的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！