配置的XBee S2与XC-TU [英] Configuring Xbee S2 with XC-TU
问题描述
我试图设置使用2的XBee模块一个非常基本的网络。作为一个协调员和其他作为路由器。
I'm trying to set up a very basic network using 2 Xbee modules. One as Coordinator and the other as Router.
问题
我只能够从Arduino的(路由器)将数据发送到XCTU(协调)。这是一个单方向的通信。什么是这些模块的正确配置,以建立双向通信?
I am only able to send data from Arduino (Router) to XCTU (Coordinator). It's a mono directional communication. What's the correct configuration for these modules in order to establish a bidirectional communication?
我按照这些教程,没有他们的工作。
I have followed these tutorials and none of them worked.
- 的http://www.seeedstudio.com/wiki/Zigbee_Networking_with_XBee_Series_2_and_Seeed%27s_Products
- http://www.digi.com/support/forum/40215/how-to-send-data-from-router-to-coordinator-in-api-mode-xbee-s2
- http://xbee.wikispaces.com/Mesh+with+Xbee
- http://www.seeedstudio.com/wiki/Zigbee_Networking_with_XBee_Series_2_and_Seeed%27s_Products
- http://www.digi.com/support/forum/40215/how-to-send-data-from-router-to-coordinator-in-api-mode-xbee-s2
- http://xbee.wikispaces.com/Mesh+with+Xbee
调制解调器版本的 XB24-ZB 。在协调有20A7固件和下面的编号:
The Modem version is XB24-ZB. The coordinator has 20A7 firmware and the following serial number:
高:13A200和低: 407B69E6
high:13A200 and low: 407B69E6
在路由器固件22A7:
高:13A200和低: 40813BFC 的
high:13A200 and low: 40813BFC
下面是协调配置:ZigBee协调器AT
Here is the Coordinator configuration: ZIGBEE COORDINATOR AT
- PAN ID:1111
- DH:13A200
- DL: 40813BFC 的(Rooter公司序号低)
- 波特率:57600
- PAN ID: 1111
- DH: 13A200
- DL: 40813BFC (Rooter serial number low)
- Baud Rate: 57600
下面是路由器配置:ZigBee路由器AT
Here is the Router Configuration: ZIGBEE ROUTER AT
- PAN ID:1111
- DH:13A200
- DL: 407B69E6 (协调员序号低)
- 波特率:57600
- PAN ID: 1111
- DH: 13A200
- DL: 407B69E6 (Coordinator serial number low)
- Baud Rate: 57600
推荐答案
如果你交换的XBee模块,并在问题跟随模块或设备(Arduino的/ XCTU)?你要确定它是否是用的XBee,或Arduino的一个问题。试试另一件将与XCTU在PC上连接两个的XBee模块的串行端口。如果数据是双向的,那么它与code或接线Arduino上的问题。
If you swap the XBee modules, does the problem follow the module or the device (Arduino/XCTU)? You want to determine whether it's an issue with the XBee, or the Arduino. Another thing to try would be connecting both XBee modules to serial ports on a PC with XCTU. If data is bi-directional, then it's an issue with the code or wiring on the Arduino.
这篇关于配置的XBee S2与XC-TU的文章就介绍到这了,希望我们推荐的答案对大家有所帮助,也希望大家多多支持IT屋!