verilog 中是否有非阻塞赋值的替代方法? [英] is there an alternative to non-blocking assignment in verilog?
本文介绍了verilog 中是否有非阻塞赋值的替代方法?的处理方法，对大家解决问题具有一定的参考价值，需要的朋友们下面随着小编来一起学习吧！
问题描述
我写了一个 Verilog 代码，这段代码描述了一个组合模块.我使用了阻塞赋值.在其他部分，必须使用非阻塞赋值.我可以在阻塞分配中使用延迟来替代非阻塞分配吗...我不想将这两个分配混合在一个模块中
I have written a Verilog code, this code to describe a combinational module. I used a blocking assignment. in other parts, there is must use a nonblocking assignment. can I use a delay in the blocking assignment to be alternative to a nonblocking assignment... I don't want to mix these two assignments in one module
`timescale 1ns / 1ps
module buffer(datain1,datain2,datain3,datain4,
s1,s2,s3,s4,s5,s6,s7,s8,s9,s10,s11,s12,
src_out1,src_out2,src_out3,
src_out4,src_out5,src_out6,
src_out7,src_out8,src_out9,
src_out10,src_out11,src_out12,
c1,c2,c3,c4,c5,c6,c7,c8,c9,c10,c11,c12,
start,clk,load2ads,rb,
post_id1,post_id2,post_id3,post_id4,
post_r1,post_r2,post_r3,post_r4);
input [9:0] post_r1,post_r2,post_r3,post_r4;
input [5:0] post_id1,post_id2,post_id3,post_id4;
input [2:0] c1,c2,c3,c4,c5,c6,c7,c8,c9,c10,c11,c12;
input [87:0] datain1,datain2,datain3,datain4; // alu result
input [5:0] s1,s2,s3,s4,s5,s6,s7,s8,s9,s10,s11,s12; // task number from ads table
input start,clk;
output reg [87:0] src_out1,src_out2,src_out3, // all information from buffer to execution array
src_out4,src_out5,src_out6, // available sources heading from buff to array
src_out7,src_out8,src_out9,
src_out10,src_out11,src_out12;
output reg rb;
output reg load2ads;
reg [9:0]a,b;
reg [263:0] // register for temporary save of alu's results
t_ads1,t_ads2,t_ads3,
t_ads4,t_ads5,t_ads6,
t_ads7,t_ads8,t_ads9,
t_ads10,t_ads11,t_ads12;
reg [29:0] temp1,temp2,temp3,temp4;
reg [9:0] buff;
reg [263:0] buffer [0:63];
reg [5:0] address_in1,address_in2,address_in3,address_in4; // register for temporary save of alu's addresses
always@(start or datain1 or datain2 or datain3 or datain4
or s1 or s2 or s3 or s4 or s5 or s6 or s7 or s8 or s9 or s10 or s11 or s12
or c1 or c2 or c3 or c4 or c5 or c6 or c7 or c8 or c9 or c10 or c11 or c12)
begin
if(start)
begin
buffer[0]= 0;
buffer[1]=264'b000100001011111100000000000100000000000000100001000000000000000000000000000000001000000000010000101111110000000000010000000000000010001100000000000000000000000000000000100000000001000010111111000000000001000000000000001001010000000000000000000000000000000010000000;
buffer[2]=264'b000100001000000100000000001000000000000010100001000000000000000000000000000000000100000000010000100000010000000000100000000001001001001100000000000000000000000000000000010000000001000010000001000000000010000000000100010101010000000000000000000000000000000001000000;
buffer[3]=264'b000100001000001000000000001100000000000000100001000000000000000000000000000000000100000000010000100000100000000000110000000000000010001100000000000000000000000000000000010000000001000010000010000000000011000000000000001001010000000000000000000000000000000001000000;
buffer[4]=264'b000100001000001100000000010000000000000000000001000000000000000000000000000000001000000000010000100000110000000001000000000000000000001100000000000000000000000000000000100000000001000010000011000000000100000000000000000001010000000000000000000000000000000010000000;
buffer[63]=264'b00000000000000000000011111100000000110000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000;
end
////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////
rb=0;
/*address_in1=datain1[65:60];
address_in2=datain2[65:60];
address_in3=datain3[65:60];
address_in4=datain4[65:60];
*/
buffer [datain1[65:60]][263:176]=datain1;
buffer [datain2[65:60]][263:176]=datain2;
buffer [datain3[65:60]][263:176]=datain3;
buffer [datain4[65:60]][263:176]=datain4;
// insert alu result into buffer and shift the data into the next ctr
if(s1 !=0)
begin
t_ads1 =buffer[s1];
if(c1==0) begin src_out1=t_ads1[263:176];src_out1[43:41]=0; end
else if(c1==1) begin src_out1=t_ads1[175:88]; src_out1[43:41]=1; end
else if(c1==2) begin src_out1=t_ads1[87:0]; src_out1[43:41]=2; end
else src_out1=0;
end
else src_out1=0;
if(s2 !=0)
begin
t_ads2 =buffer[s2];
if(c2==0) begin src_out2=t_ads2[263:176];src_out2[43:41]=0;end
else if(c2==1) begin src_out2=t_ads2[175:88]; src_out2[43:41]=1;end
else if(c2==2) begin src_out2=t_ads2[87:0]; src_out2[43:41]=2;end
else src_out2=0;
end
else src_out2=0;
if(s3 !=0)
begin
t_ads3 =buffer[s3];
if(c3==0) begin src_out3=t_ads3[263:176];src_out3[43:41]=0; end
else if(c3==1) begin src_out3=t_ads3[175:88];src_out3[43:41]=1; end
else if(c3==2) begin src_out3=t_ads3[87:0];src_out3[43:41]=2; end
else src_out3=0;
end
else src_out3=0;
////////////////////////////////////////////////////////////////
if(s4 !=0)
begin
t_ads4 =buffer[s4];
if(c4==0) begin src_out4=t_ads4[263:176]; src_out4[43:41]=0; end
else if(c4==1) begin src_out4=t_ads4[175:88]; src_out4[43:41]=1; end
else if(c4==2) begin src_out4=t_ads4[87:0];src_out4[43:41]=2; end
else src_out4=0;
end
else src_out4=0;
if(s5 !=0)
begin
t_ads5 =buffer[s5];
if(c5==0) begin src_out5=t_ads5[263:176]; src_out5[43:41]=0; end
else if(c5==1) begin src_out5=t_ads5[175:88]; src_out5[43:41]=1; end
else if(c5==2) begin src_out5=t_ads5[87:0]; src_out5[43:41]=2; end
else src_out5=0;
end
else src_out5=0;
if(s6 !=0)
begin
t_ads6 =buffer[s6];
if(c6==0) begin src_out6=t_ads6[263:176]; src_out6[43:41]=0; end
else if(c6==1) begin src_out6=t_ads6[175:88]; src_out6[43:41]=1; end
else if(c6==2) begin src_out6=t_ads6[87:0]; src_out6[43:41]=2; end
else src_out6=0;
end
else src_out6=0;
///////////////////////////////////////////////////////////////////////////
if(s7 !=0)
begin
t_ads7 =buffer[s7];
if(c7==0) begin src_out7=t_ads7[263:176]; src_out7[43:41]=0; end
else if(c7==1) begin src_out7=t_ads7[175:88]; src_out7[43:41]=1; end
else if(c7==2) begin src_out7=t_ads7[87:0]; src_out7[43:41]=2; end
else src_out7=0;
end
else src_out7=0;
if(s8 !=0)
begin
t_ads8 =buffer[s8];
if(c8==0) begin src_out8=t_ads8[263:176]; src_out8[43:41]=0; end
else if(c8==1) begin src_out8=t_ads8[175:88]; src_out8[43:41]=1; end
else if(c8==2)begin src_out8=t_ads8[87:0];src_out8[43:41]=2; end
else src_out8=0;
end
else src_out8=0;
if(s9 !=0)
begin
t_ads9 =buffer[s9];
if(c9==0)begin src_out9=t_ads9[263:176]; src_out9[43:41]=0; end
else if(c9==1)begin src_out9=t_ads9[175:88]; src_out9[43:41]=1; end
else if(c9==2)begin src_out9=t_ads9[87:0]; src_out9[43:41]=2; end
else src_out9=0;
end
else src_out9=0;
/////////////////////////////////////////////////////////////////////
if(s10 !=0)
begin
t_ads10 =buffer[s10];
if(c10==0)begin src_out10=t_ads10[263:176]; src_out10[43:41]=0; end
else if(c10==1)begin src_out10=t_ads10[175:88];src_out10[43:41]=1; end
else if(c10==2)begin src_out10=t_ads10[87:0];src_out10[43:41]=2; end
else src_out10=0;
end
else src_out10=0;
if(s11 !=0)
begin
t_ads11 =buffer[s11];
if(c11==0)begin src_out11=t_ads11[263:176];src_out11[43:41]=0; end
else if(c11==1)begin src_out11=t_ads11[175:88];src_out11[43:41]=1; end
else if(c11==2)begin src_out11=t_ads11[87:0];src_out11[43:41]=2; end
else src_out11=0;
end
else src_out11=0;
if(s12 !=0)
begin
t_ads12 =buffer[s12];
if(c12==0)begin src_out12=t_ads12[263:176];src_out12[43:41]=0; end
else if(c12==1)begin src_out12=t_ads12[175:88];src_out12[43:41]=1; end
else if(c12==2)begin src_out12=t_ads12[87:0];src_out12[43:41]=2; end
else src_out12=0;
end
else src_out12=0;
这部分我想用等价的替代方式
this part I want to use an equivalent alternative way
if((datain1[49]==1)||(datain2[49]==1)||(datain3[49]==1)||(datain4[49]==1))
begin
buffer[1][59:50] <=buffer[1][147:138];
buffer[1][147:138]<=buffer[1][235:226];
buffer[2][59:50] <=buffer[2][147:138];
buffer[2][147:138]<=buffer[2][235:226];
buffer[3][59:50] <=buffer[3][147:138];
buffer[3][147:138]<=buffer[3][235:226];
buffer[4][59:50] <=buffer[4][147:138];
buffer[4][147:138]<=buffer[4][235:226];
buffer[5][59:50] <=buffer[5][147:138];
buffer[5][147:138]<=buffer[5][235:226];
buffer[6][59:50] <=buffer[6][147:138];
buffer[6][147:138]<=buffer[6][235:226];
buffer[7][59:50] <=buffer[7][147:138];
buffer[7][147:138]<=buffer[7][235:226];
buffer[8][59:50] <=buffer[8][147:138];
buffer[8][147:138]<=buffer[8][235:226];
buffer[9][59:50] <=buffer[9][147:138];
buffer[9][147:138]<=buffer[9][235:226];
buffer[10][59:50] <=buffer[10][147:138];
buffer[10][147:138]<=buffer[10][235:226];
buffer[11][59:50] <=buffer[11][147:138];
buffer[11][147:138]<=buffer[11][235:226];
buffer[12][59:50] <=buffer[12][147:138];
buffer[12][147:138]<=buffer[12][235:226];
buffer[13][59:50] <=buffer[13][147:138];
buffer[13][147:138]<=buffer[13][235:226];
buffer[14][59:50] <=buffer[14][147:138];
buffer[14][147:138]<=buffer[14][235:226];
buffer[15][59:50] <=buffer[15][147:138];
buffer[15][147:138]<=buffer[15][235:226];
buffer[16][59:50] <=buffer[16][147:138];
buffer[16][147:138]<=buffer[16][235:226];
buffer[17][59:50] <=buffer[17][147:138];
buffer[17][147:138]<=buffer[17][235:226];
buffer[18][59:50] <=buffer[18][147:138];
buffer[18][147:138]<=buffer[18][235:226];
buffer[19][59:50] <=buffer[19][147:138];
buffer[19][147:138]<=buffer[19][235:226];
buffer[20][59:50] <=buffer[20][147:138];
buffer[20][147:138]<=buffer[20][235:226];
buffer[21][59:50] <=buffer[21][147:138];
buffer[21][147:138]<=buffer[21][235:226];
buffer[22][59:50] <=buffer[22][147:138];
buffer[22][147:138]<=buffer[22][235:226];
buffer[23][59:50] <=buffer[23][147:138];
buffer[23][147:138]<=buffer[23][235:226];
buffer[24][59:50] <=buffer[24][147:138];
buffer[24][147:138]<=buffer[24][235:226];
buffer[25][59:50] <=buffer[25][147:138];
buffer[25][147:138]<=buffer[25][235:226];
buffer[26][59:50] <=buffer[26][147:138];
buffer[26][147:138]<=buffer[26][235:226];
rb=1;
end
end
endmodule
推荐答案
你不应该在组合逻辑中使用非阻塞赋值理想情况下.
You should not use Nonblocking Assignments in Combinational logic ideally.
因此，在您的设计中，在时序方面存在严重问题.
但是，如果您使您的设计同步，那么您可以通过在 Systemverilog 中使用 Clocking Block 来避免使用 NBA.
However, if you make your design synchronous, then you can avoid the usage of NBA with the use of Clocking Block in Systemverilog.
clocking cb @(posedge clk)
input a, b, c;
// Other Signals as per your requirement
endclocking
现在在时钟块中声明的输入默认具有 #1step 延迟，这意味着它们将保存当前时隙的前置区域或前一个时隙的延迟区域(两者相等)的值).
Now the inputs declared in the clocking block by default have #1step delay, which means that they will hold the value of preponed region of current timeslot or postponed region of previous timeslot (which both are equal).
因此，您可以在设计中的任何位置使用这些信号，并且可以消除对 NBA 的使用.
Hence you can use those signals anywhere in your design and you can eliminate the usage of NBA.
但是，需要注意的一件事是时钟块不可综合.
这是一个工作示例:
module temp();
reg a, b, c;
reg clock;
initial
begin
$monitor("@%0t: a - %b, b - %b, c - %b", $time(), a, b, c);
clock = 1;
a = 1;
b = 0;
c = 1;
#100 $finish();
end
always #5 clock = ~clock;
clocking cb @(negedge clock);
input a, b, c;
endclocking
always @(posedge clock)
begin
a = cb.c;
b = cb.a;
c = cb.b;
end
endmodule
请注意，如果您保持时钟事件和始终阻止事件相同(如posedge/negedge)，那么它们与作为时钟块输入采样的值之间可能存在潜在的竞争条件可能不准确.
这篇关于verilog 中是否有非阻塞赋值的替代方法?的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！
查看全文
