Arduino 频率为 11.0592MHz.修改 Timer0, delayMicroseconds() [英] Arduino at 11.0592MHz. Modify Timer0, delayMicroseconds()

问题描述

我在 Arduino 环境中使用 11.0592MHz 的 ATMega328P.我认识到 delayMicroseconds() 函数的速度太快了大约 27%.原因是，wiring.c 中的代码假设时钟速度现在为 8MHz.

I am using the ATMega328P at 11.0592MHz with the Arduino environment. I recognized that the delayMicroseconds() function is about 27% too fast. The reason is, that the code in wiring.c assumes that the clock peed is now 8MHz.

现在我尝试修复它.我找到了不同的帖子，但我不确定最兼容 Arduino 的方式是什么.你能推荐什么?

Now I try to fix it. I found different posts but I am not sure what is the most Arduino compatible way. What can you recommend?

1. 如果 F_CPU 为 11.0592MHz，将wiring.c 中的变量us"乘以1.27?简单，但只影响 delayMicroseconds 而不是 millis()、micros()、delay() 等.
2. 将预缩放因子从 64 更改为 ???

其他想法或指南?

提前致谢.

菲利克斯

推荐答案

Arduino 的方式是为您的开发板制作一个具有新 F_CPU 速度的定制平台.核心库应该通过这个 F_CPU.

The Arduino way would be to make a custom PLATFORM for your board with that of the new F_CPU speed. The core libraries should carry this F_CPU through.

这很容易，通过使用您的差异制作 board.txt 文件.文件的位置(两者之间相同)在两个当前 IDE 之间不同.以 Arduino IDE 1.0.5 为例:

This is easy enough, by making a boards.txt file with your differences. Where the location of the file (same between the two) is different between the two current IDE's. In the case of Arduino IDE 1.0.5:

C:\Users\mflaga\Documents\Arduino\hardware\myArduino11MgHz\boards.txt

C:\Users\mflaga\Documents\Arduino\hardware\myArduino11MgHz\boards.txt

在 1.5.5 的情况下:

and in the case of 1.5.5:

C:\Users\mflaga\Documents\Arduino\hardware\myArduino11MgHz\avr\boards.txt

C:\Users\mflaga\Documents\Arduino\hardware\myArduino11MgHz\avr\boards.txt

在您的情况下，草图目录会有所不同.

Where in your case the sketch directory would be different.

# See: http://code.google.com/p/arduino/wiki/Platforms

##############################################################

myArduino11MgHz.name=Arduino 11MgHz

myArduino11MgHz.vid.0=0x2341
myArduino11MgHz.pid.0=0x0043
myArduino11MgHz.vid.1=0x2341
myArduino11MgHz.pid.1=0x0001

myArduino11MgHz.upload.tool=avrdude
myArduino11MgHz.upload.protocol=arduino
myArduino11MgHz.upload.maximum_size=32256
myArduino11MgHz.upload.maximum_data_size=2048
myArduino11MgHz.upload.speed=115200

myArduino11MgHz.bootloader.tool=avrdude
myArduino11MgHz.bootloader.low_fuses=0xFF
myArduino11MgHz.bootloader.high_fuses=0xDE
myArduino11MgHz.bootloader.extended_fuses=0x05
myArduino11MgHz.bootloader.unlock_bits=0x3F
myArduino11MgHz.bootloader.lock_bits=0x0F
myArduino11MgHz.bootloader.file=optiboot/optiboot_atmega328.hex

myArduino11MgHz.build.mcu=atmega328p
myArduino11MgHz.build.f_cpu=11059200L
myArduino11MgHz.build.board=AVR_myArduino11MgHz
myArduino11MgHz.build.core=arduino:arduino
myArduino11MgHz.build.variant=arduino:standard

##############################################################

这是 board.txt 的第 3 方 GUI 编辑器.

Here is a 3rd party GUI Editor of the board.txt.

免责声明.以上确实可以编译并且应该可以正常工作.我还没有实际测试并加载到单元中的地方.

Disclaimer. The above does compile and should work fine. Where I have not actually tested and loaded into a unit.

也就是说，我希望引导加载程序的 F_CPU 不匹配.对此有三种可能的解决方案.

That said, I would expect the bootloader's F_CPU not to match. There are three possible solutions to this.

第一；optiboot 加载程序应该有一个对应的目标，其偏差如下:

First; the optiboot loader should have a corresponding target with the below deviation:

\arduino-1.5.5\hardware\arduino\avr\bootloaders\optiboot\Makefile

\arduino-1.5.5\hardware\arduino\avr\bootloaders\optiboot\Makefile

myArduino11MgHz: AVR_FREQ = 11059200L

第二；更改boards.txt上传速度以匹配=115200*(11059200/16000000)的变化.

Second; Change the boards.txt upload speed to match the change of =115200*(11059200/16000000).

myArduino11MgHz.upload.speed=79626

这是一个非典型的波特率，avrdude 或串口可能支持它.

This being a non typical baud rate, either avrdude or the serial port may support it.

第三；不要使用引导加载，通过 ISP 编程器上传.

Third; Don't use the bootload, by uploading via the ISP programmer.

我也计划用不同的 F_CPU 制作一块板，但实际上只制作了具有相同速度的定制板.对于您的情况，我很想知道上述方法是否真的有效.

I have likewise planned to make a board with a different F_CPU, but only actually made custom boards, with the same speed. I would be curious to know if the above actually works, in your case.

这篇关于Arduino 频率为 11.0592MHz.修改 Timer0, delayMicroseconds()的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！