在CentOS 5.2上安装NTFS文件系统 [英] Mounting NTFS filesystem on CentOS 5.2

问题描述

我想在CentOS 5.2中安装一些内部和外部NTFS驱动器，最好在启动时自动安装。

编辑：感谢所有的答案，我总结了他们下面=）

解决方案

回答我自己的问题：PostMan和mgb导致我的路径正确，包含完整的解决方案。

注意：有关此问题的简短手册/ wiki在这里： http://wiki.centos.org/TipsAndTricks/NTFSPartitions

所以，我使用一个全新的，的CentOS 5.2与最新更新。首先，我运行 su 命令以避免任何权限问题。

的外部NTFS驱动器：

  mkdir / mnt / iomega80 
 mkdir / mnt / iogear250 
  

我不得不使用fdisk命令，但它不在我的系统。以下是安装的方法：

  yum install util-linux 
  

然后我运行 / sbin / fdisk -l <​​/ code>，找到设备名称：

磁盘/ dev / sdc：250.0 GB，250059350016字节
255磁头，63扇区/磁道，30401气缸
单位= 16065 * 512 = 8225280字节

设备引导开始结束块标识系统
** / dev / sdc1 ** * 1 30401 244196001 7 HPFS / NTFS

磁盘/ dev / sdd：82.3 GB，82348278272字节
255磁头，63扇区/磁道，10011磁柱
单位= 16065 * 512 = 8225280字节的柱面

设备引导开始结束块系统
** / dev / sdd1 ** * 1 10011 80413326 7 HPFS / NTFS


对我来说，它们是 / dev / sdc1 和 / dev / sdd1 。

我不得不安装NTFS-3G，这是一个在CentOS上支持NTFS支持的软件包。要安装NTFS-3G，我首先必须在YUM存储库列表中包括RPMFORGE。

要在YUM存储库列表中包含RPMFORGE，我使用了以下说明： http://rpmrepo.org/RPMforge/Using 。对于我的系统，我不得不运行的两个命令是：

  wget http://packages.sw.be/rpmforge- release / rpmforge-release-0.3.6-1.el5.rf.i386.rpm 
 rpm -Uhv rpmforge-release-0.3.6-1.el5.rf.i386.rpm 
  
 
 <$ p $ 
 p>  yum install fuse fuse-ntfs-3g dkms dkms-fuse 
  

最后，我可以使用mount命令安装文件系统：

  mount -t ntfs-3g / dev / sdc1 / mnt / iogear250 
 mount -t ntfs-3g / dev / sdd1 / mnt / iomega80 
  

这两行到 / etc / fstab ，像以前的答案建议，我得到的驱动器挂载在启动：

  / dev / sdc1 / mnt / iogear250 ntfs-3g rw，umask = 0000，defaults 0 0 
 / dev / sdd1 / mnt / iomega80 ntfs-3g rw，umask = 0000，默认值0 0 
  




I want to mount some internal and external NTFS drives in CentOS 5.2, preferably automatically upon boot-up. Doesn't matter if it's read/write or read-only, but read/write would be preferred, if it's safe.

Edit: Thanks for all answers, I summarized them below =)

解决方案

To answer my own question: PostMan and mgb led me to the right path, but their answers did not contain complete solution.

Note: A short manual/wiki on this question is here: http://wiki.centos.org/TipsAndTricks/NTFSPartitions

So, I am using a fresh, bare install of CentOS 5.2 with latest updates. First of all, I ran the su command to avoid any permission issues.

I created mount points for a couple of external NTFS drives:

mkdir /mnt/iomega80
mkdir /mnt/iogear250

I had to use the fdisk command, but it wasn't in my system. Here's what installs it:

yum install util-linux

Then I ran /sbin/fdisk -l and found the device names:

Disk /dev/sdc: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
**/dev/sdc1**   *           1       30401   244196001    7  HPFS/NTFS

Disk /dev/sdd: 82.3 GB, 82348278272 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
**/dev/sdd1**   *           1       10011    80413326    7  HPFS/NTFS

For me, they are /dev/sdc1 and /dev/sdd1.

I had to install NTFS-3G, a package that enables NTFS support on CentOS. To install NTFS-3G, I first had to include RPMFORGE in YUM repository list.

To include RPMFORGE in YUM repository list, I used these instructions: http://rpmrepo.org/RPMforge/Using. For my system, the two commands I had to run were:

wget http://packages.sw.be/rpmforge-release/rpmforge-release-0.3.6-1.el5.rf.i386.rpm
rpm -Uhv rpmforge-release-0.3.6-1.el5.rf.i386.rpm 

Finally, I installed NTFS-3G using this YUM command:

yum install fuse fuse-ntfs-3g dkms dkms-fuse

At last, I could use the mount command to mount the filesystems:

mount -t ntfs-3g /dev/sdc1 /mnt/iogear250
mount -t ntfs-3g /dev/sdd1 /mnt/iomega80

By adding these two lines to /etc/fstab, like previous answers suggested, I got the drives to mount upon boot-up:

/dev/sdc1               /mnt/iogear250          ntfs-3g rw,umask=0000,defaults 0 0
/dev/sdd1               /mnt/iomega80           ntfs-3g rw,umask=0000,defaults 0 0

这篇关于在CentOS 5.2上安装NTFS文件系统的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！