Basys2上的七段多路复用 [英] Seven Segment Multiplexing on Basys2
问题描述
这是我的第一篇文章，所以我希望我做的正确.我试图在BASYS2板上的四位数七段显示器上输出"4 3 2 1".我已检查以确保0启用信号并且我已正确映射端口.我认为该错误在我的多路复用逻辑内，因为我只能显示一位数字.我是Verilog的新手(曾经使用过C语言)，希望您能提出任何建议.谢谢
this is my first post so I hope I'm doing this correctly. I'm trying to output a "4 3 2 1" on a four digit seven segment display on a BASYS2 board. I have checked to make sure that 0 enables the signal and that I have the ports mapped correctly. I believe the error is within my multiplexing logic since I am only able to display a single digit. I'm new to Verilog (am used to C) and would appreciate any suggestions. Thanks
`timescale 1ns / 1ps
module main (clock, AN0, AN1, AN2, AN3, CA, CB, CC, CD, CE, CF, CG, CDP);
//USED FOR SEVEN SEG
input clock;
output AN0, AN1, AN2, AN3, CA, CB, CC, CD, CE, CF, CG, CDP;
reg [7:0] cathodedata; //cathode data
reg [3:0] anodedata; //anode data
reg [2:0] digit = 1;
reg [6:0] data;
reg setdp;
reg [19:0] counter = 0;
assign CA = cathodedata [7];
assign CB = cathodedata [6];
assign CC = cathodedata [5];
assign CD = cathodedata [4];
assign CE = cathodedata [3];
assign CF = cathodedata [2];
assign CG = cathodedata [1];
assign CDP = cathodedata [0];
assign AN3 = anodedata [3];
assign AN2 = anodedata [2];
assign AN1 = anodedata [1];
assign AN0 = anodedata [0];
//USED FOR SEVEN SEG
//Multiplexing
//Board Clock: 50MHz
//p = t*f
//t = 16ms
//p = 16ms * 50*10^6 = 800,000 cycles
//200,000 cycles for each digit
//Refreshed every 16ms (~60Hz)
always@(negedge clock)
begin
if (digit == 1)
begin
if (counter == 200_000)
begin
digit = 2;
end
else
begin
counter = counter + 1;
data = 4;
end
end
else if (digit == 2)
begin
if (counter == 400_000)
begin
digit = 3;
end
else
begin
counter = counter + 1;
data = 3;
end
end
else if (digit == 3)
begin
if (counter == 600_000)
begin
digit = 4;
end
else
begin
counter = counter + 1;
data = 2;
end
end
else if (digit == 4)
begin
if (counter == 800_000)
begin
digit = 1;
counter = 0;
end
else
begin
counter = counter + 1;
data = 1;
end
end
end
always @ (*)
begin
case (data)
6'd0: cathodedata = 8'b00000011; //0
6'd1: cathodedata = 8'b10011111; //1
6'd2: cathodedata = 8'b00100101; //2
6'd3: cathodedata = 8'b00001101; //3
6'd4: cathodedata = 8'b10011001; //4
6'd5: cathodedata = 8'b01001001; //5
6'd6: cathodedata = 8'b01000001; //6
6'd7: cathodedata = 8'b00011111; //7
6'd8: cathodedata = 8'b00000001; //8
6'd9: cathodedata = 8'b00001001; //9
6'd10: cathodedata = 8'b00010001; //A
6'd11: cathodedata = 8'b11000001; //B
6'd12: cathodedata = 8'b01100011; //C
6'd13: cathodedata = 8'b10000101; //D
6'd14: cathodedata = 8'b00100001; //E
6'd15: cathodedata = 8'b01110001; //F
default: cathodedata = 8'b11111111; //default all off
endcase
if (setdp == 1) //decimal point
cathodedata = cathodedata & 8'hFE;
case(digit)
0: anodedata = 4'b1111; //all OFF
4: anodedata = 4'b1110; //AN0
3: anodedata = 4'b1101; //AN1
2: anodedata = 4'b1011; //AN2
1: anodedata = 4'b0111; //AN3
default:
anodedata = 4'b1111; //all OFF
endcase
end
endmodule
推荐答案
我也正在使用basys2并寻找7段驱动程序. Nathan G的代码对我不起作用(也许使用系统Verilog吗?)，但我发现了这篇文章:
I too am using a basys2 and looking for a 7-seg driver. Nathan G's code did not work for me (using system verilog perhaps?), but I found this article: http://simplefpga.blogspot.co.uk/2012/12/scrolling-or-moving-text-using-7.html?showComment=1362783256904#c5783969326158067433 and I cannibalized it to my own ends.The modified code is below. It should take (although I haven't checked the decoding fully yet) four hex values and display them on the 7-seg. In my example my board now says 'FAAF' (because getting this working was faf)
从谨慎网站获取的ucf文件:
ucf file taken from digilent site:
# Pin assignment for DispCtl
# Connected to Basys2 onBoard 7seg display
NET "seg<0>" LOC = "L14"; # Bank = 1, Signal name = CA
NET "seg<1>" LOC = "H12"; # Bank = 1, Signal name = CB
NET "seg<2>" LOC = "N14"; # Bank = 1, Signal name = CC
NET "seg<3>" LOC = "N11"; # Bank = 2, Signal name = CD
NET "seg<4>" LOC = "P12"; # Bank = 2, Signal name = CE
NET "seg<5>" LOC = "L13"; # Bank = 1, Signal name = CF
NET "seg<6>" LOC = "M12"; # Bank = 1, Signal name = CG
NET "dp" LOC = "N13"; # Bank = 1, Signal name = DP
NET "an<3>" LOC = "K14"; # Bank = 1, Signal name = AN3
NET "an<2>" LOC = "M13"; # Bank = 1, Signal name = AN2
NET "an<1>" LOC = "J12"; # Bank = 1, Signal name = AN1
NET "an<0>" LOC = "F12"; # Bank = 1, Signal name = AN0
顶级模块具有此功能:
module top_level(
//clock input
input CLK,
output [7:0] seg,
output dp,
output [3:0] an
);
scrolling_name scrolling_name(
.clock(CLK),
.reset(RESET),
.a(seg[0]),
.b(seg[1]),
.c(seg[2]),
.d(seg[3]),
.e(seg[4]),
.f(seg[5]),
.g(seg[6]),
.dp(dp),
.an(an),
//.XPosition(XPosition),
//.YPosition(YPosition)
.XPosition(8'hFA),
.YPosition(8'hAF)
);
endmodule
和我从链接中的那个家伙那里拿到的文件经过编辑后是:
and the file I took from the guy in the link and have edited is:
`timescale 1ns / 1ps
module scrolling_name(
input clock,
input reset,
output a,
output b,
output c,
output d,
output e,
output f,
output g,
output dp,
output [3:0] an,
input [7:0] XPosition,
input [7:0] YPosition
);
reg [28:0] ticker; //to hold a count of 50M
wire click;
reg [3:0] fourth, third, second, first; // registers to hold the LED values
always @ (posedge clock or posedge reset) //always block for the ticker
begin
if(reset)
ticker <= 0;
else if(ticker == 50000000) //reset after 1 second
ticker <= 0;
else
ticker <= ticker + 1;
end
reg [3:0] clickcount; //register to hold the count upto 9. That is why a 4 bit register is used. 3 bit would not have been enough.
assign click = ((ticker == 50000000)?1'b1:1'b0); //click every second
always @ (posedge click or posedge reset)
begin
if(reset)
clickcount <= 0;
else if(clickcount == 8)
clickcount <= 0;
else
clickcount <= clickcount + 1;
end
always@(posedge clock)
begin
fourth = XPosition[7:4];
third = XPosition[3:0];
second = YPosition[7:4];
first = YPosition[3:0];
end
//see my other post on explanation of LED multiplexing.
localparam N = 18;
reg [N-1:0]count;
always @ (posedge clock or posedge reset)
begin
if (reset)
count <= 0;
else
count <= count + 1;
end
reg [6:0]sseg;
reg [3:0]an_temp;
always @ (*)
begin
case(count[N-1:N-2])
2'b00 :
begin
sseg = first;
an_temp = 4'b1110;
end
2'b01:
begin
sseg = second;
an_temp = 4'b1101;
end
2'b10:
begin
sseg = third;
an_temp = 4'b1011;
end
2'b11:
begin
sseg = fourth;
an_temp = 4'b0111;
end
endcase
end
assign an = an_temp;
reg [6:0] sseg_temp;
always @ (*)
begin
case(sseg)
0 : sseg_temp = 7'b1000000; //to display 0
1 : sseg_temp = 7'b1001111; //to display 1
2 : sseg_temp = 7'b0100100; //to display 2
3 : sseg_temp = 7'b0110000; //to display 3
4 : sseg_temp = 7'b0011001; //to display 4
5 : sseg_temp = 7'b0010010; //to display 5
6 : sseg_temp = 7'b0000011; //to display 6
7 : sseg_temp = 7'b1111000; //to display 7
8 : sseg_temp = 7'b0000000; //to display 8
9 : sseg_temp = 7'b0011000; //to display 9
10 : sseg_temp = 7'b0001000; //to display A
11 : sseg_temp = 7'b0000011; //to display B
12 : sseg_temp = 7'b1000110; //to display C
13 : sseg_temp = 7'b0100001; //to display D
14 : sseg_temp = 7'b0000110; //to display E
15 : sseg_temp = 7'b0001110; //to display F
default : sseg_temp = 7'b1111111; //blank
endcase
end
assign {g, f, e, d, c, b, a} = sseg_temp;
assign dp = 1'b1;
endmodule
请原谅可怕的格式/缩进-他和我的结合在一起，并添加了四个空格以使堆栈溢出以将其识别为代码.我没有时间使事情变得很不幸.如果您愿意，我可以将所有这些捆绑在一起，然后放到保管箱中.
Please excuse the horrible formatting/indenting - there is a combination of his, mine, and adding four spaces to get stack overflow to recognize it as code. I don't have time to make things pretty unfortunately. I can bundle all this together and put it on dropbox if you would like.
内森
这篇关于Basys2上的七段多路复用的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！
