zigbee运动检测传感器的使用 [英] zigbee motion detect sensor usage

问题描述

我以前的经验是能够接收我的温度/湿度Zigbee传感器发送的数据. 另外，我能够发送命令来控制Zigbee功率计/开关.

我购买了带有文件的运动检测传感器，该文件包含一行IAS数据包. 我知道这是IAS ZONE设备.

有人能让我知道使用这种传感器的第一步是什么吗?

我刚刚在zigbee网关上启用了允许连接255，但运动检测传感器似乎未加入网络.

谢谢

@tc，

再尝试两次加入网络后，它终于可以工作了. 感谢您的答复，我们将按照您提供的步骤进行操作.

解决方案

为什么说它没有加入网络，是否用数据包嗅探器验证了它没有加入并发送设备通知，还是没有?以与温度/湿度传感器相同的方式发送报告或响应读取的属性?

如果它确实没有加入，则IAS设备上可能有一个按钮将触发加入.或者它可能已经连接到网络并且需要重置.

将IAS区域设备加入网络后，IAS设备将不会自动发送温度/湿度传感器之类的报告.您需要先注册.为此，请编写IAS区域端点的CIE IEEE地址属性，并将其设置为网关(或CIE)的IEEE地址.您可能需要使用活动的EP请求和简单描述符请求来发现端点ID.设置CIE IEEE地址属性后，它应该发送一个区域注册请求，您应该发送一个区域注册响应，然后在触发警报或其他区域事件时，IAS区域设备将发送网关/CIE区域状态更改通知.

有关CIE IEEE地址属性和区域注册要求/Rsp的更多信息，请参考ZCL规范 http://www.zigbee.org/download/standards-zigbee-cluster-library/.

关于， TC.

My prior experience is able to receive the data sent from my temperature / humidity zigbee sensor. Also, I am able to send the command to control the zigbee power meter/switch.

I bought a motion detect sensor with a document contains a line of IAS packet. I know it's a IAS ZONE device.

Could anyone let me know what is the first step to handle with this kinda sensor?

I just enabled the permit-join 255 on my zigbee gateway but the motion detect sensor seems not to join the network.

Thanks

@tc,

After trying two more times to join the network, it finally works. Thanks for your reply and I will work on the steps as you provided.

解决方案

Why do you say it is not joining the network, have you verified with a packet sniffer that it is not joining and sending a device announce, or is it not sending reports or responding to read attributes in the same way as your temp/humidity sensors?

If it is really not joining then there maybe a button on the IAS device that will trigger a join. Or it may already be connected to a network and need resetting.

After you have joined the IAS Zone device to the network the IAS device will not automatically send reports like the temp/humidity sensors. You will need to enroll it first. Do this by writing the CIE IEEE Address attribute for the IAS Zone Endpoint and set it to the IEEE address of you Gateway (or CIE). You may need to discover the endpoint ID with active EP request, and Simple Descriptor Request. After setting the CIE IEEE Address attribute it should then send a Zone Enrollment Request, you should send a Zone Enrollment Response and then the IAS Zone device will send Gateway/CIE Zone State Change Notifications when an Alarm or other Zone event is triggered.

For more info on the CIE IEEE Address attribute and the Zone Enrollment Req/Rsp refer to the ZCL Specification http://www.zigbee.org/download/standards-zigbee-cluster-library/.

Regards, TC.

这篇关于zigbee运动检测传感器的使用的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持IT屋！